ROEQI
Route equipment initiate
Format
ROEQI:ROU=,TRU=[,EQU=][,IP=][,INDDAT=][,CNTR=]; |
|
CNTRL = |
Controlling side indicator. The parameter can be used only in combination with ITU-T method 2 line selection and it can only be used with a CCSS7 trunk. If the parameter is omitted when initiating a CCSS7 trunk, it will be set to NO. The parameter has no significance when initiating any other trunk and will be left out. |
EQU = |
Equipment position. Equipment position for external line. This parameter is normally mandatory, but when initiating external lines for H.323 routes, the parameter must be omitted. |
INDDAT = |
Individual trunk data for external line. If the parameter is omitted the value H"0000000000FF is assumed to apply. |
IP = |
IP address. IP address of a network interface at the remote end. This parameter is used only for external destinations that can be reached via H.323 routes. |
ROU = |
Route number. |
TRU = |
Trunk line number. LIM and sequence number for the external line. & and && are allowed for this parameter. |
Function
The command is used to initiate one or more equipment positions as external lines of a previously initiated route.
The external lines for H.323 routes shall be initiated without equipment position. These external lines will dynamically allocate an equipment position when required.
One or more lines can be initiated at the same time in a LIM, the line that comes first is associated with the equipment position stated. The rest of the external lines are associated with the subsequent free equipment positions of the right type in the same LIM.
Note: Only one external line at a time can be initiated when signaling equipment is to be affiliated to the line.
If an external line that requires individual data shall be initiated, these individual data shall be stated at the initiation. If several external lines are initiated at the same time, all these will receive the same individual data.
The order of selecting an external line (of a route) within a LIM is controlled by the sequence number of the line. The lines within the LIM are scanned, starting with the line with the lowest sequence number.
The order of selecting an external line when the lines of the route are divided over several LIMs is controlled by the programming order, that is, the order in which the external lines were initiated in the different LIMs.
Example 1
Initiate external lines for route 1. The lines are to be placed in LIM 1, where they will have sequence numbers 7 and 8. The lines are to be connected to gateway A, magazine 1, board position 10, where the line with serial number 7 is to be connected to board individual number 0. The first free equipment position of the right type in LIM 1 is to be associated with the line with sequence number 8.
ROEQI:ROU=1,TRU=1-7&1-8,EQU=1A-1-10-7; |
EXECUTED |
Example 2
Initiate an external line for route 5. The line is to be placed in LIM 1, where it will have sequence number 3. The line is to be connected to gateway B, magazine 1, board position 10, where the line with sequence number 3 is to be connected to board individual 0. The external line shall have the individual data 000000000003.
ROEQI:ROU=5,TRU=1-3,EQU=1B-1-10-3,INDDAT=000000000003; |
EXECUTED |
Example 3
Initiate an external CCSS7 line for route 7. The line is to be placed in LIM 1, where it will have sequence number 1. The line is to be connected to gateway C, magazine 0, board position 40, where the line with sequence number 1 is to be connected to board individual number 1. The line should be controlled by the own exchange.
ROEQI:ROU=7,TRU=1-1,EQU=1C-0-40-1,CNTRL=YES; |
EXECUTED |
Example 4
Initiate external lines for route 2, which is an H.323 route. These lines are to be placed in LIM 3, where they will have sequence numbers 5 and 6.
ROEQI:ROU=2,TRU=3-5&3-6; |
EXECUTED |
Example 5
Initiate external lines for route 2, which is an H.323 route. These lines are to be placed in LIM 3, where they will have sequence numbers 7 and 8, and they will be associated a destination IP address different from the IP address tied to the route.
ROEQI:ROU=2,TRU=3-7&3-8, IP=192.4.6.87; |
EXECUTED |
Command Category
Dangerous = No